?006 fairchild semiconductor corporation 1 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers march 2007 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers features dv/dt of 600v/? guaranteed compact 4-pin surface mount package (2.4mm maximum standoff height) zero voltage crossing p eak blocking voltage: 600v (fodm306x) 800v (fodm308x) av ailable in tape and reel quantities of 500 and 2500. c-ul, ul and vde certi?ations pending applications solenoid/valve controls lighting controls static power switches ac motor drives t emperature controls e.m. contactors ac motor starters solid state relays description the fodm306x and fodm308x series consist of an infrared emitting diode optically coupled to a monolithic silicon detector performing the function of a zero voltage crossing bilateral triac driver, and is housed in a compact 4-pin mini-?t package. the lead pitch is 2.54mm. they are designed for use with a triac in the interface of logic systems to equipment powered from 115/240 vac lines, such as solid state relays, industrial controls, motors, solenoids and consumer appliances. pa ck ag e dimensions 4.40 0.20 2.54 0.25 3.60 0.30 2.00 0.20 0.10 0.10 0.40 0.10 5.30 0.30 7.00 +0.2 ?.7 0.20 0.05 main term. 1 2 anode cathode 3 4 main term. zero crossing circuit note: all dimensions are in millimeters.
2 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers absolute maximum ratings (t a = 25? unless otherwise speci?d) symbol parameter rating units total pa ckage t stg storage temperature -55 to +150 ? t opr operating temperature -40 to +100 ? emitter i f (avg) continuous forward current 60 ma i f (pk) p eak forward current (1? pulse, 300pps.) 1 a v r reverse input voltage 6 v p d po w er dissipation (no derating required over operating temp. range) 100 mw detector i t(rms) on-state rms current 70 ma (rms) v drm off-state output terminal voltage fodm3062/fodm3063 600 v fodm3082/fodm3083 800 p d po w er dissipation (no derating required over operating temp. range) 300 mw
3 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers electrical characteristics (t a = 25?) individual component characteristics t ransfer characteristics zero crossing characteristics isolation characteristics notes: * all typicals at 25?. 1. test voltage must be applied within dv/dt rating. 2. this is static dv/dt. see figure 1 for test circuit. commutating dv/dt is function of the load-driving thyristor(s) only. 3. all devices are guaranteed to trigger at an i f value less than or equal to max i ft . therefore, recommended operating i f lies between max i ft (10ma for fodm3062/82, 5ma for fodm3063/83) and absolute max i f (60 ma). 4. steady state isolation voltage, v iso , is an internal device dielectric breakdown rating. for this test, pins 1 & 2 are common, and pins 3 & 4 are common. symbol parameter test conditions min. typ.* max. units emitter v f input forward voltage i f = 30ma 1.5 v i r reverse leakage current v r = 6v 100 ? detector i drm1 p eak blocking current, either direction rated v drm , i f = 0 (1) 500 na dv/dt critical rate of rise of off-state voltage i f = 0 (figure 1) (2) 600 v/? symbol dc characteristics test conditions device min. typ.* max. units i ft led trigger current main terminal v oltage = 3v (3) fodm3062 10 ma fodm3082 fodm3063 5 fodm3083 i h holding current, either direction all 300 ? v tm p eak on-state voltage, either direction i f = rated i ft , i tm = 100ma peak all 3 v symbol characteristics test conditions device min. typ.* max. units v ih inhibit voltage, mt1-mt2 voltage above which device will not trigger i f = rated i ft all 20 v idrm2 leakage in inhibit state i f = rated i ft , rated vdrm, off-state all 500 ? characteristics test conditions symbol device min. typ.* max. units steady state isolation v oltage (4) (1 minute) r.h. = 40% to 60% v iso all 3750 vrms
4 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers t ypical performance curves fig. 1 led forward voltage vs. forward current fig. 2 leakage current vs. ambient temperature fig. 3 holding current vs. ambient temperature fig. 4 trigger current vs. ambient temperature i f - forward current (ma) 110 100 v f - forward voltage (v) 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.8 1.7 t a = -40 c t a = 25 c t a = 100 c t a - am bient temperature ( c) -40 -20 0 20 4 06080100 i drm - le akage current (na) 0.1 1 10 100 1000 vdrm = 600v t a - ambient temperature ( c) -40 -20 100 i h - holding current (normalized) 0.1 1.0 10 020406 080 normalized to t a = 25 c t a - ambient temperature ( c) -40 -20 0 20 40 60 80 i ft - trigger current (normalized) 0.8 0.6 0.8 1.0 1.2 1.4 1.6 v tm = 3v normalized to t a = 25 c 100
5 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers t ypical performance curves fig. 7 on-state characteristics v tm - on-state voltage (v) -4 -3 -2 -1 0 1 2 3 4 i tm - on-state current (ma) -800 -600 -400 -200 0 200 400 600 800 t a = 25 c fig. 5 led current required to trigger vs. led pulse width fig. 6 off-state output terminal voltage vs. ambient temperature pw in - led trigger pulse width ( c) 110 100 i ft - led trigger current (normalized) 0 2 4 6 8 10 12 t a in >> 100 s normalized to pw a t= 25 c a normalized to t = 25 c t a - ambient temperature ( c) v drm - off-state output terminal voltage (normalized) 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 -40 -20 020406 080100
6 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers t ypical performance curves figure 8. static dv/dt test circuit vdc 800v (fodm3082) (fodm3083) 600v (fodm3062) (fodm3063) r = 10 k ? c test x100 scope probe pulse input mercury wetted relay 378v (fodm3062, fodm3063) 504v (fodm3082, fodm3083) 0 volts applied voltage wa veform v max = dv/dt = 0.63 v max r test d.u.t. d.u.t. rc rc = 800v (fodm3082, fodm3083) = 600v (fodm3062, fodm3063) = 378 rc (fodm3062, fodm3063) = 504 rc (fodm3082, fodm3083) figure 9. hot-line switching application circuit 0.01 v cc r in 1 2 4 3 240 vac hot neutral 360 ? * fo r highly inductive loads (power factor < 0.5), change this value to 360 ohms. 330 fodm3062 fodm3063 fodm3082 fodm3083 39* load ty pical circuit for use when hot line switching of 240vac is required. in this circuit the ?ot side of the line is sw itched and the load connected to the cold or neutral side. the load may be connected to either the neutral or hot line. r in is calculated so that i f is equal to the rated i ft of the part, 5ma for the fodm3063/83 and 10ma for the fodm3062/82. the 39 ? resistor and 0.01 f capacitor are fo r snubbing of the triac and may or may not be necessary depending upon the particular triac and load used. note: this optoisolator should not be used to drive a load directly. it is intended to be a trigger device only. 1. the mercury wetted relay provides a high speed repeated pulse to the d.u.t. 2. 100x scope probes are used, to allow high speeds and vo ltages. 3. the worst-case condition for static dv/dt is established by triggering the d.u.t. with a normal led input current, then removing the current. the variable rtest allows the dv/dt to be gradually increased until the d.u.t. continues to trigger in response to the applied voltage pulse, even after the led current has been removed. the dv/dt is then decreased until the d.u.t. stops triggering. trc is measured at this point and recorded. figure 10. inverse-parallel scr driver circuit (240vac) v cc r in 1 2 4 3 240 vac scr 360 ? r1 d1 scr r2 d2 load suggested method of firing two, back-to-back scr s, with a fairchild triac driver. diodes can be 1n4001; resistors, r1 and r2, are optional 330 ohms. note: this optoisolator should not be used to drive a load directly. it is intended to be a trigger device only. fodm3062 fodm3063 fodm3082 fodm3083
7 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers ordering information marking information option description no option bulk (100 units/tube) v vde approved r1 tape and reel (500 units) r2 tape and reel (2500 units) r1v tape and reel (500 units) and vde approved r2v tape and reel (2500 units) and vde approved 1 2 6 4 3 5 de?itions 1f airchild logo 2d e vice number 3 vde mark (note: only appears on parts ordered with vde option ?see order entry table) 4 one digit year code 5t wo digit work week ranging from ?1 to ?3 6 assembly package code 3063 x vr yy
8 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers t ape and reel information d d w k t d 1 0 p p a p 0 b 0 0 2 e f w 1 0 r1 reel diam eter r2 devices pe r reel max. com pon ent rotatio n or tilt cover tape thicknes s cover tape wid th pocket hole di a. pocket dim ension pocket loc ation sprocket h ole location sprocket h ole dia. sprocket ho le pitch tape thickness pocket pitc h tape wid th symbo l de scription r1 r2 b d w 1 d k 0 1 0 e a p 0 p f 2 d p 0 0 t w 178 mm (7") 330 mm (13") dime nsions 12.00 0.3 7.45 0.1 20 ? max 500 1.50 0.1 2.45 0.1 0.06 2 0.02 9.30 0.1 1.75 0.1 8.00 0.1 2.00 0.1 5.50 0.1 3.90 0.1 1.50 0.1 4.00 0.1 0.30 0.05 2.54 pitch 2500
9 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers footprint drawing for pcb layout recommended infrared relow soldering pro?e note: all dimensions are in mm. 0.80 6.50 2.54 1.00 ? peak reflow temperature: 260 c (package surface temperature) ? time of temperature higher than 245 c: 40 seconds or less ? number of reflows: 3 300 250 200 temperature ( c) 150 100 50 0 50 0 100 150 200 250 300 time (s) 10 s 260 c 245 c 40 s
10 www.fairchildsemi.com fodm306x/fodm308x rev. 1.0.4 fodm3062/fodm3063/fodm3082/fodm3083 4-pin full pitch mini-flat package zero-cross triac driver output optocouplers tradem a rks the following are registered and unregistered trademarks fairchild semiconductor owns or is authorized to use and is not intend ed to be an exhaustive list of all such trademarks. acex ? across the board. around the world. activearray bottomless build it now coolfet crossvolt ctl? current transfer logic? dome e 2 cmos ecospark ? ensigna fact quiet series? fact ? fast ? fastr fps frfet ? globaloptoisolator gto hisec i-lo implieddisconnect intellimax isoplanar microcoupler micropak microwire msx msxpro ocx ocxpro optologic ? optoplanar ? pacman pop power220 ? power247 ? poweredge powersaver powertrench ? programmable active droop qfet ? qs qt optoelectronics quiet series rapidconfigure rapidconnect scalarpump smart start spm ? stealth? superfet supersot -3 supersot -6 supersot -8 syncfet? tcm the power franchise ? ? tinyboost tinybuck tinylogic ? tinyopto tinypower tinywire trutranslation p serdes uhc ? unifet vcx wire disclaimer fairchild semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. fairchild does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. these specifications do not expand the terms of fairchild?s worldwide terms and conditions, specifically the warranty therein, which covers these products. life support policy fairchild?s products are not authorized for use as critical components in life support devices or systems without the express written approval of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems wh ich, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform w hen properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. product status definitions definition of terms datasheet identification product status definition advance information formative or in design this datasheet contains the design specifications for product development. specifications may change in any manner without notice. preliminary first production this datasheet contains preliminary data; supplementary data will be published at a later date. fairchild semiconductor reserves the right to make changes at any time without notice to improve design. no identification needed full production this datasheet contains final specifications. fairchild semiconductor reserves the right to make changes at any time without notice to improve design. obsolete not in production this datasheet contains specifications on a product that has been discontinued by fairchild semiconductor. the datasheet is printed for reference information only. re v. i24
|
